The Makita RF1101 can work with several router lifts, but its smaller motor diameter means compatibility differs from common 3.5-inch router motors.
Makita identifies the RF1101 as a 2-1/4 HP variable-speed router. Router-lift manufacturers commonly reference the Makita 1101 family, with Kreg documenting a motor diameter of approximately 3.218 inches.
This guide summarizes the Makita RF1101 router lift relationships currently researched by Wood Tool Guide.
Makita RF1101 Compatibility at a Glance
Kreg PRS5000 — Manufacturer Verified
Kreg’s PRS5000 documentation lists the Makita 1101 with a motor diameter of approximately 3.218 inches.
Kreg provides a dedicated clamp-block configuration for this smaller motor.
Wood Tool Guide status: Manufacturer Verified
Requirement: Set the PRS5000 clamp blocks to hole pattern 8.
JessEm Mast-R-Lift II — Manufacturer Verified
JessEm includes the Makita 1101 among the router motors supported by the Mast-R-Lift II.
Wood Tool Guide status: Manufacturer Verified
Requirement: Follow JessEm’s installation instructions for the Makita 1101 motor.
JessEm Rout-R-Lift 3.5XT — Requires Modification
The Rout-R-Lift 3.5XT is primarily designed around 3.5-inch router motors.
JessEm lists the Makita 1101 as compatible through its optional 3D-printable adjustable collar, rather than as a standard direct fit.
Wood Tool Guide status: Requires Modification
Requirement: Optional adjustable collar specified by JessEm for the Makita 1101.
Rockler Pro Lift — Unverified
Wood Tool Guide has not found sufficient current manufacturer documentation explicitly listing the Makita RF1101 as a supported Rockler Pro Lift motor.
Wood Tool Guide status: Unverified
This does not mean the combination is incompatible. It means we do not currently have enough authoritative evidence to label the relationship Manufacturer Verified.
Why the RF1101 Is Different From Common 3.5-Inch Routers
The Makita RF1101 motor is smaller than the approximately 3.5-inch motors used by routers such as the Bosch 1617 and DeWalt DW618.
That difference matters because router lifts need to clamp the motor securely.
Some multi-router lifts accommodate the smaller Makita motor through adjustable clamping systems. Other lifts may require a collar or another manufacturer-specified solution.
This is why motor diameter is useful information—but diameter alone does not prove compatibility.
Makita RF1101 vs “Makita 1101”
Compatibility documentation does not always use exactly the same model naming convention.
Makita’s official model is RF1101, while router-lift manufacturers may shorten the reference to Makita 1101.
Wood Tool Guide considers the manufacturer’s model identity and supporting documentation when recording these relationships rather than relying only on a shortened model name.
What “Requires Modification” Means Here
A Requires Modification result does not necessarily mean drilling, cutting or permanently altering the router.
For the JessEm Rout-R-Lift 3.5XT relationship, the issue is that the smaller Makita motor requires the manufacturer-specified adjustable collar.
Wood Tool Guide uses Requires Modification whenever an adapter, collar, drilling or another stated change is necessary compared with the lift’s standard direct-fit installation.
Why “Unverified” Does Not Mean “Incompatible”
This distinction is important.
Unverified means we have insufficient authoritative evidence to claim that a particular combination fits.
Incompatible is reserved for cases where authoritative evidence indicates that the combination does not fit or function correctly.
We deliberately avoid converting an absence of evidence into an incompatibility claim.
Router Lift Compatibility vs Router Table Compatibility
Even after confirming that the RF1101 fits a particular router lift, you still need to verify whether that lift fits your router table.
Check both:
- Router → Lift: Does the lift support the Makita RF1101 motor?
- Lift → Table: Does the lift plate fit your router table opening or mounting system?
Both relationships matter when assembling the complete system.
Before Buying a Router Lift for a Makita RF1101
Confirm:
- your exact Makita router model,
- whether the lift manufacturer explicitly supports the 1101/RF1101 family,
- whether the motor fits directly,
- whether a collar or special clamp configuration is required,
- and whether the lift plate fits your router table.
Do not assume that a lift designed for 3.5-inch motors will automatically accommodate the smaller RF1101.
Check Makita RF1101 Compatibility
Use our Router Lift Compatibility Finder to see the Makita RF1101 relationships currently recorded in the Wood Tool Guide database.
Check Router Lift Compatibility →
Each researched relationship includes its status, installation requirement where applicable, evidence type and source-check date.
Compatibility information can change as manufacturers revise products and documentation. Wood Tool Guide records the evidence source and date checked for each researched relationship. Always review the linked manufacturer documentation before purchasing or installing equipment.